Used Barges

Shipping Pt. / Location: UNITED KINGDOM, SOUTHPORT LANCASHIRE
Blown film lines and bag makers. Selection of used blown film lines and bag makers for sale in UK.

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: USA, BARBERTON OHIO
Prodex Extruder. 4 1/2" 24/1 Vented Extruder 200 HP

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: USA, BARBERTON OHIO
Sterling Extruder. 4 1/2" Vented 36/1 150 HP Extruder 80s Vintage

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: ITALY, ISSOGNE AOSTA
GAMMA MECCANICA TANDEM 125 RECYCLING LINE. GAMMAMECCANICA TANDEM SYSTEM 125 mm. 950 kg/h double screening Throughput rate up to 600-950 kg/h ca, depending on material and feeding rate (0,30-0,40 Kwh/kg) Line suitable for the recycling for heavily printed, high humidity and contaminated materials. High performance degassing chamber for removal of up to 10 times more gas and humidity in the melted material compared to other systems (so you can save on the cost of an agglomerator) The line includes : Loading conveyor belt tunnel metal detector automatic compactor N.2 Dosing unit for masterbatches and more 1st extruder with 125 mm. screw Ø 28 L/D 1st degassing point FIMIC RAS 500 fully automatic screenchanger control cabinet 2nd extruder with 140 mm. screw Ø 18 L/D 2nd degassing point BD-PLAST non-stop screen-changer TDA6 GM water ring pelletizer heat exchanging unit vibrating screen blower Water treatment unit, mechanical type, with non woven filtering Electric cabinet for complete management of the line The line is in excellent conditions with very few worked hours Can be tested in Italy on appointment

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: USA, SAN MARCOS CALIFORNIA
Used Jun gheinrich Electric Forklift 4000 lbs. Working Condition. Two cells of battery not working. Need change battery.

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: USA, RANBURNE ALABAMA
Economy 60AH36 Baler. 7" bore, 39" stroke has manual and auto cycle with electronic eye. Panel set for 230v 3 phase, 20hp. Uses 11 gauge x 15' wire,manual tie, under power now. Main and door cylinders repacked with little use since. Has 8' long x 5' tall x 27" wide hopper going to 27"×30" approx.feed opening.

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: BRAZIL, PENáPOLIS SãO PAULO
Hydraulic Press with Heated Plates. Plates Dimension: 4,000 mm x 3,000 mm; • Opening between upper and lower plates: 1,200mm; • Minimum piston stroke: 500mm; • Closing force: 4,500 Ton (45 MN); • Maximum working temperature: 200°C; • Closing and opening speed: 2.5 mm/s - Auxiliary pistons for fast movement; • Heating by thermal oil with 4 heated zones on each plate; • Voltage: 380V; • Cart for automatic movement of the mold (entering and exiting the press).

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: USA, PHOENIX ARIZONA
Parts for CP 250 Can Flattener & Blower. 2- Magnet Head pulleys, 1- New Conveyor Belt. bearings, Drive Belt.

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---

Shipping Pt. / Location: USA, NORTH CHILI NEW YORK
Balemaster Auto-Tie Baler (Brand New). 2025 Balemaster Model E-915 12" main cylinder, 100hp, 27.5" x 40" feed chute BRAND NEW and comes with remainder of factory warranty. Selling at 27% discount and available immediately.

To view contact information or reply to this listing,
ENTER YOUR EMAIL ADDRESS AND CLICK GO :

---